Ask Seller
Brandt "KDF 520" Edgebander - Pre-mill (2007) 
Ended
J-Kraft in Houston, TX
- Winning Bid : $3,551.00 USD Sold
- 28 Bid(s)
- High Bidder: L****c
Assets No Longer Required - Houston, TX ( Closed #28074821 )
Brandt Edgebander and Voorwood Shape and Sand
-
Item Location
Houston, TX
-
Make
Brandt
-
Model
"KDF 520"
-
Serial Number
0-261-02-2823
-
Year
2007
-
Phase
3 PHASE
-
Voltage
230 VOLT
-
Inspection Date
By Appointment only - Please e-mail requests to: [email protected]
-
Final Removal Date
-
Estimated Dimensions
172" x 48" x 72"
-
Estimated Weight
3,500 Lbs.
-
Seller Comment
A non negotionable loading fee has been established - See below. This includes the rigging and loading onto a flat bed trailer. Requests for additional labor, crating or pallatization will be extra.
-
Load Fee
$250
-
page views
2078
Edge thickness cap. 0.4 - 8 mm (5/16") , panel thickness of 8 mm - 50 mm (5/16" - 2"), Min. panel length 160 mm (6-3/8") & 65 mm (2-1/2") min. width.
Line control (NO limit switches) for workstation function; signal infeed light to insure proper spacing between panels.
Height adjustment with top pressure beam for all workstations, equipped with digital height indicator.
Power Control PC 20+ Control with: 13-1/2" VGA Screen, 8 MB IDE flash disk, 8 MB RAM, internal Modem for remote diagnostic link.
(2) Motor Pre-Milling Unit with: (2) 3 HP motors (12,000 RPM) to clean-up potential chipped edges.
Quick heat-up glue system (approx. 12 Min) w/quick change glue tank for maintenance & glue color change.
Glue temperature indicator for both the glue pot & glue roller with LED thermostat, automatic temperature setback if the machine is idle for (15) Min or more.
The glue applicator roller is reversible & retractable from the fence line.
Automatic magazine for strip & coil (large 800 mm dia. coil table to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine,
Pressure Section, (1) drive plus (2) idle rollers "pneumatically controlled" pressure section.
End Trimming: (0.25 HP - 12,000 RPM motors), chamfers 0° - 15°.
Flush/Radius/Bevel Trimming: Top & bottom, bevels 0° - 15° (0.5 HP - 12,000 RPM motor).
Scraping Unit: Top & bottom for 3 mm radius, pneumatically controlled indexing system.
Buffing Unit: Top & bottom (0.25 HP - 2,800 motors).
Please note: Seller has indicated the screen stopped working a few weeks before the new Bander arrived. They continued to use this machine w/o the screen until there new bander arrived. An external monitor may be able to attached in lieu of replacing factory monitor
The information provided in this lot was gathered from literature, internet & physical inspection. It is thought to be accurate; but not guaranteed. Bidders are urged to use the open house or private inspection periods to inspect and verify.
The listed specifications & information were taken from the manufacturer’s published information, internet research, or seller’s description.
The specifications & information are assumed to be correct; however, in no way, guaranteed. Bidders are encouraged to inspect the machine, call with questions, or contact the manufacturer for more information.
Please log in to view the bid history
LoginPick-ups are to be scheduled by appointment only. Please contact Sabrina Burns at 209-839-7707 or [email protected] to schedule an appointment. For freight quotes please contact Aaron at All-Ways Trucking at 541-608-6532. Buyer bears all costs to remove and load this lot. Buyer must remove entire lot purchased. Anyone removing non-hand carriable lots must provide MachineryMax, Inc. with a certificate of insurance (COI) before purchased items can be removed.
All buyers agree to make full payment to MachineryMax, Inc. within 48 hours of the online closing date for the auction lots purchased. All invoices over $1,500.00 are to be made by bank wire transfer or cashier’s check payable to MachineryMax, Inc. Purchases under $1,500.00 may be made using Visa, MasterCard, or American Express (2% credit card processing fee will be added to the invoice). All payments are to be made in USD currency only. Bidder represents and warrants to MachineryMax, Inc. that such bidder has immediately available funds to fully pay for its successful bids within 48 hours of the online closing date. All payment questions should be directed to Sabrina Burns at 209-839-7707 or [email protected] All buyers agree that there will be a 15% Buyers premium that will be added to the final invoice.