SCM GROUP MODEL #K360-ERT AUTOMATIC EDGEBANDER WITH PRE-MILL AND CORNER ROUNDING

YEAR 2015 MACHINE

230 VOLT, 3-PHASE MACHINE

SERIAL #AH/118373

K 360 ERT1 – Single Sided Automatic Edgebander

Automatic single sided edgebander designed to be used for edgebanding straight vertical profiles with coiled material (veneer and PVC) and with strips (high-pressure laminate and solid wood) with a maximum thickness of 8mm.

Machine Base

The machine base is made of a tubular steel structure and is designed to assure maximum stability and accuracy.

Top Pressure Beam

All operating units raise and lower simultaneously when the pressure beam is adjusted. No adjustment is required for the glue roller when changing panel thickness. The pressure beam has two rows of staggered pressure rollers with steel bearings.

Capacities And Speed

• Edgebanding thickness: .4mm - 6mm (.016-1/4”)
• Guillotine capacity: 3mm
• Feed speed: 36 ft/min.
• Panel height: 3/8” min – 2 1/2” max
• Minimum panel length: 5 1/2”
• Minimum panel width: 2 3/8”
• Minimum distance between panels: 20”

Glue Station

Teflon coated glue pot to facilitate glue changeover. Warm up time is approximately eight to ten minutes. The unit is also equipped with a quick disconnect plug for changing from one pot to another.

Pressure Section

There are a total of three pressure rollers for pressing the banding to the workpiece edge. The first roller is powered,, it is also Teflon coated to prevent the banding material from slipping. The two idle rollers have opposing one-degree tilt to provide extra pressure along the top and bottom edge. The machine comes standard with an automatic strip magazine. Comes standard with a mechanical digital readout for the positioning of the pressure section.

Control Panel

The K 360 series is equipped with a Orion 1 Plus controller, fixed, located at the infeed of the machine. It is capable of operating all the work units via soft touch buttons, it pneumatically tilt’s the end trim unit from the control panel, it eliminates the use of micro switches, as well as control the temperature of the glue. It is tilted slightly upward for a more ergonomically friendly position for the operator.

Adjustable Infeed Fence

The infeed fence is manually adjustable with pneumatic positioning in/out.

“RT-VP” Pre-Milling Station:

To rectify/clean panels already sized and squared before the edge is applied. The unit is composed of two high frequency motors (2.0hp) with jumping action controlled through the PLC.  The cutting heads are adjustable vertically. Diamond Pre-Mill Cutters are standard.

End Trimming Station

This unit is composed of two independent .25 hp motors mounted on THK guides. End trim utilizes a draw cut system for reduced blade projection on thick panels. The unit comes standard with automatic tilting of the unit from the control panel with two preset positions.

Edge Trimming Station

This unit is composed of two independent .7 hp motors operating at 12,000 rpm. It comes standard with THREE position pneumatics, this allows the operator to go from thin tape, to 3mm pvc, to solid wood, through the control panel. The unit is equipped with both a set of 15 degree insert conical cutters and a 3mm radius set of insert cutters. All adjustments are carried out with mechanical digital readouts. The unit has top and bottom copy wheels and side copy shoes. The motors have quick release plugs to facilitate tooling changes.

Corner Rounding Unit

Single motor unit, .50hp,  designed to carry out the rounding of edges on 3mm material. Comes standard with a diamond cutterhead. The unit is equipped with front and lateral copying devices and pneumatic blowers to clean the panel. The unit can go from thin tape to 3mm PVC, through the controller, with no manual adjustments by the operator.

“RAS-V” Profile Scraping Station

Scraping station designed to remove knife marks from thick PVC.  The unit is equipped with pneumatic in/out positioning from the control panel. It has a large diameter horizontal copy wheel and side copy wheel device with digital indicators. The unit is also equipped with dust extraction and a separate collection bin.

RC-V Glue Scraping Unit

The unit eliminates any excess glue to help improve the quality of the glue joint. It comes standard with double copy wheels on the top and bottom of the panel, air blowers are standard to help keep the knives clean, the off fall is collected in the collection bin and it is pneumatically positioned through the controller.

Buffing Unit

The buffing unit has two .25 hp motors. It can also be tilted up to 12 degrees to provide a softer, more refined edge finish.

Acoustical Safety Enclosure

All working units are enclosed under an acoustical safety hood to reduce noise and prevent accidents. The hood has a safety microswitch which prevents the machine from operating when the hood is open.

Centralized Dust Extraction

Machine comes with two 3” ports for the premilling station, two 2” ports for the top and bottom trim station and one 3” port for the 3mm collection bin for extraction.

Technical Specifications