event-image

IDM IDIMATIC 66-20 EDGEBANDER WITH PREMILL, VISTA CALIFORNIA

City, State
Closed
IDM Idimatic 66-20 Edgebander with Pre Mill Located in Vista CA

Edgebanding thickness capacity, 10 -- 50 mm (3/8" -- 2") panel thickness, 60 mm (2-3/8") minimum panel width & 140 mm (5-1/2") minimum length Pre-milling station with (2) 3 HP -- 12,000 RPM counter rotating vertical milling heads: both with pneumatic jump control, 30 mm spindles and SIKO digital readouts for setup & adjustments, fully enclosed by noise insulated cabin Front & rear end trims (motors 0.8 HP -- 14,400 RPM each), motors tilt 0° - 12° on horizontal plane, 2nd blade setup allows 45° chamfer cut Top & bottom rough trims (motors 2.5 HP -- 14,400 RPM each), tilts 0- 30° Top & bottom fine/bevel/profile multi-function trims (motors 0.9 HP -- 12,000 RPM each), tilts 0°- 10° for bevel and 3 mm PVC corner round (prepared for "quick change" of motors, for interchangeable 2nd set of bevel/radius trim units) Corner rounding units from trimming leading & trailing upper and lower edge/corners when edgebanding all (4) sides or when edgebanding "soft- or postformed" panels (4 motors 0.8 HP -- 14,400 RPM each), 1" maximum radius Top & bottom scrapers for up to 5MM thick PVC banding, pneumatic pressure control for scraping knives, digital readouts, overhead PVC filter unit eliminates PVC chips being sucked in by dust collector; top & bottom PVC edge color & surface reactivation unit, hot air blower with temperature adjustment Top & bottom "oscillating" buffing (0.25 HP -- 1,680 RPM motors), units tilt 0° - 30°. Multi-function trimmer, corner rounding unit & scraper with "pneumatic exclusion" controlled from operator panel Function & line control with microprocessor Microprocessor displays stored data, on/off workstation sequence & trouble shooting diagnostic; data input by alphanumeric keyboard; microprocessor adjusts according to stored programs or input; top pressure beam opening, pressure section position & pressure control, in/out pneumatic sideways positioning of "trim/scrap/ corner round" workstations, on/off sequence of workstation motors Equipped with automatic strip & coil feed magazine with 3 mm PVC guillotine (9" pack capacity for strips) 8.8 Lbs. capacity overhead granular glue "Quick Melt" hopper feeding compact size, Teflon coated lower applicator glue pot, 1" diameter glue applicator roller, reversible rotation by flip of switch Pressure section with (1) large diameter (7-7/8") clutch controlled drive roller and (4) jump action, pneumatic pressure idle rollers, horizontal Adjustment w/digital indicator Hardened steel link feed chain with "anti-slip" 80 mm wide rubber pads (2) feed speeds 40 & 60 FPM, with 3 HP drive Motorized adjustment of top pressure beam. Heated infeed fence, automatic panel spacing control, remote control job button, insulated sound enclosure over all trim stations; rotating operator control panel at eye-level height, 15 KVA -- 240 Hz frequency inverter & complete set of used tooling 220V, 60 Cy, 3 Ph Dimensions: 4'W X 81"H X 25'L WT. 5000 LBS. Replacement value: $150,000.00 SEE IT IN ACTION https://www.youtube.com/watch?v=BlsDpnaMNPY

Event ID:
6800670
Starts:
5/3/2017 5:00:00 PM PT
First Lot Closes:
5/31/2017 3:00:00 PM PT
# of Lots:
1
This auction uses Proxy Bidding
Managed by:
Managed by MACHINERY MAX @ 209-832-0100
Terms and conditions Value added service options
Closes
05/31/2017
Pick Up Location
VISTA CALIFORNIA
This auction event is closed.