Bidding has ended on this item.
#LOT003

Polmac "Akron 245" Edgebander (2006) Ended

Excess Machinery in Continuing Operations...Georgetown, TX

  • Winning Bid : $3,601.00 USD Sold
  • 67 Bid(s)
  • High Bidder: J****e
Documents
No documents available
Bidding Info
This auction uses Proxy Bidding.
Bids placed within the final 5 minutes will extend the auction closing time by 5 minutes.
img

Georgetown Millworks - Excess Machinery - Georgetown, TX ( Closed #14858702 )

Georgetown Millworks...Excess Machinery...Changing directions.

  • Item Location

    Georgetown, TX

  • Make

    Polmac

  • Model

    "Akron 245" Edgebander (2006)

  • Serial Number

    6889

  • Year

    2006

  • Phase

    3 PHASE

  • Voltage

    230 VOLT

  • Inspection Date

    By Appointment only - Please e-mail requests to: [email protected]

  • Final Removal Date

    03/18/2019

  • Estimated Dimensions

  • Estimated Weight

    1,700 kG

  • Seller Comment

    A non negotionable loading fee has been established - See below

  • page views

    1140

0.4 - 8 mm (5/16") Cap. edgebanding thickness, min. panel width 85 mm & min. length 140 mm, panel thickness 10 - 50 mm; automatic strip & coil feed magazine with robust shear type 3 mm PVC guillotine;

NC controlled adjustable top pressure beam positioning.  Hot-Melt glue system (12 min. heat up time) with Teflon coated gluepot, digital thermostats with automatic kick-down when machine is in idle mode. 

1" Dia. glue applicator roller; pressure section with (1) large dia. "non-stick" coated drive roller & (2) chrome plated idle rollers with pneumatic positioning.

Front & rear end trims (0.33 HP - 12,000 RPM motors), motors travel on (2) straight slides and pneumatic tilt 0° - 25° on horz. plane. 

Top & Bottom flush trims with "Quick Change" motors (1.0 HP - 12,000 RPM motors), digital readouts for easy setup.  2-Motor (0.3 HP - 12,000 RPM motors) corner rounding unit for trimming leading & trailing upper & lower edge/corners, and can be used as a second Top & Bottom fine trimmer as well. 

Top & bottom scrapers for 3 mm thick PVC banding, digitals for horiz. adjustments.  Top & bottom buffing (0.5 HP - 2,800 RPM motors), units tilt 0° - 30°. Top & bottom (2,000 Watt) hot air blowers with temperature adjustment. 


Feed Speed 39 FPM, 3 HP feed drive.

Listed specifications were taken from the manufacturer’s published information and is assumed to be correct but not guaranteed.

Bidder is encouraged to inspect the machine, call with questions contact the manufacturer for more information.

Please log in to view the bid history

Pick-ups are to be scheduled by appointment only. Please contact Sabrina Burns at 209-839-7707 [email protected] to schedule an appointment.  For freight quotes please contact Aaron at All-Ways Trucking at 541-608-6532. Buyer bears all costs to remove and load this lot. Buyer must remove entire lot purchased.  Anyone removing non-hand carriable lots must provide MachineryMax, Inc. with a certificate of insurance (COI) before purchased items can be removed.

CONTACT ALWAYS TRUCKING 541-608-6532
$0.00 USD
LOADING FEE
$150.00 USD

All buyers agree to make full payment to MachineryMax, Inc. within 48 hours of the online closing date for the auction lots purchased. All invoices over $1,500.00 are to be made by bank wire transfer or cashier’s check payable to MachineryMax, Inc. Purchases under $1,500.00 may be made using Visa MasterCard, or American Express (2% credit card processing fee will be added to the invoice). All payments are to be made in USD currency only. Bidder represents and warrants to MachineryMax, Inc. that such bidder has immediately available funds to fully pay for its successful bids within 48 hours of the online closing date. All payment questions should be directed to Sabrina Burns at 209-839-7707 or [email protected] All buyers agree that there will be a 15% Buyers premium that will be added to the final invoice.