× Bidding has ended on this item.

IDM IDIMATIC 66-20 EDGEBANDER WITH PREMILL, VISTA CALIFORNIA (Closed #11364946)

Terms & Conditions
Shipping Information
This Event Uses Proxy Bidding.

IDM Idimatic 66-20 Edgebander with Pre Mill

Located in Vista, Ca

  Lot # 001
 
Listing Image
Description

Edgebanding thickness capacity, 10 -- 50 mm (3/8" -- 2") panel thickness, 60 mm (2-3/8") minimum panel width & 140 mm (5-1/2") minimum length

Pre-milling station with (2) 3 HP -- 12,000 RPM counter rotating vertical milling heads: both with pneumatic jump control, 30 mm spindles and SIKO digital readouts for setup & adjustments, fully enclosed by noise insulated cabin

Front & rear end trims (motors 0.8 HP -- 14,400 RPM each), motors tilt 0° - 12° on horizontal plane, 2nd blade setup allows 45° chamfer cut

Top & bottom rough trims (motors 2.5 HP -- 14,400 RPM each), tilts 0- 30°

Top & bottom fine/bevel/profile multi-function trims (motors 0.9 HP -- 12,000 RPM each), tilts 0°- 10° for bevel and 3 mm PVC corner round (prepared for "quick change" of motors, for interchangeable 2nd set of bevel/radius trim units)

Corner rounding units from trimming leading & trailing upper and lower edge/corners when edgebanding all (4) sides or when edgebanding "soft- or postformed" panels (4 motors 0.8 HP -- 14,400 RPM each), 1" maximum radius

Top & bottom scrapers for up to 5MM thick PVC banding, pneumatic pressure control for scraping knives, digital readouts, overhead PVC filter unit eliminates PVC chips being sucked in by dust collector; top & bottom PVC edge color & surface reactivation unit,  hot air blower with temperature adjustment

Top & bottom "oscillating" buffing (0.25 HP -- 1,680 RPM motors), units tilt 0° - 30°.

Multi-function trimmer, corner rounding unit & scraper with "pneumatic exclusion" controlled from operator panel

Function & line control with microprocessor

Microprocessor displays stored data, on/off workstation sequence & trouble shooting diagnostic; data input by alphanumeric keyboard; microprocessor adjusts according to stored programs or input; top pressure beam opening, pressure section position & pressure control, in/out pneumatic sideways positioning of "trim/scrap/ corner round" workstations, on/off sequence of workstation motors

Equipped with automatic strip & coil feed magazine with 3 mm PVC guillotine (9" pack capacity for strips)

8.8 Lbs. capacity overhead granular glue "Quick Melt" hopper feeding compact size, Teflon coated lower applicator glue pot, 1" diameter glue applicator roller, reversible rotation by flip of switch

Pressure section with (1) large diameter (7-7/8") clutch controlled drive roller and (4) jump action, pneumatic pressure idle rollers, horizontal Adjustment w/digital indicator

Hardened steel link feed chain with "anti-slip" 80 mm wide rubber pads

(2) feed speeds 40 & 60 FPM, with 3 HP drive

Motorized adjustment of top pressure beam. Heated infeed fence, automatic panel spacing control, remote control job button, insulated sound enclosure over all trim stations; rotating operator control panel at eye-level height, 15 KVA -- 240 Hz frequency inverter & complete set of used tooling

220V, 60 Cy, 3 Ph

 

Dimensions: 4'W X 81"H X 25'L    WT. 5000 LBS.

 

Replacement value: $150,000.00

Buyers Premium
  • 10.00 %
Current Bid $1,000.00 USD   ( ) Unsuccessful
Buy Now Price $0.00 USD
No Reserve     Available for immediate purchase.
End Date  [Extended]
Bid History 0 Bids  
High Bidder
Listed By   MDM
Watching 7
Page Views 292
Additional Information
Located Vista, CA
MAKE IDM
MODEL Idimatic 66-20 Edgebander with Pre Mill
SERIAL NUMBER ALH/000058
YEAR 1998
PHASE 3 PHASE
VOLTAGE 230 VOLT
ESTIMATED WEIGHT 5000 lbs.
Shipping
  • CONTACT ALWAYS TRUCKING 541-608-6532:  $0.00 USD
  • CONTACT LOCAL RIGGER:  $0.00 USD